Technology of Placing gypsum tiles with your hands

Gypsum tiles have to be laid properly, as not just the aesthetic look of cosmetic facing, but also the service quality of the

substance will be dependent on the engineering of work. The product is more also universal, and it can be attached to plaster,

concrete, brick or gypsum board sheets, and provided that the surface of the base is even and has no defects.

If the flaws of this foundation are important, it ought to be thoroughly treated with primer, and then a cement mortar is made,

which fills all the cracks. Then the surface should be primed and dried. Primer treatment is necessary to improve the bond between

the tile and the walls. In this case, its composition should pick a special, comprising elements which stop the look of fungus and


In today’s interior of these rooms most often used gypsum tiles, even imitating natural stone or brick. To perform decorative

finishing your self, it’s necessary firstly to select a scheme of tile placement and prepare a solution. It is necessary to focus

on the reverse side of the substance. If its surface includes an embossed surface, then the adhesive should be placed having an

trowel, and if it’s even, then with a notched one.

The technologies of the job is as follows:

* A thin layer of adhesive mortar is put on the pre-prepared wall. It is spread over the base so it is likely to place 4-5

tiles. Decorative cladding may be put both on plasterboard, also on putty.

* Cover the back side of these tiles with glue.

* Plaster elements are pressed against the walls and their location is corrected. To align with the seams, it is recommended to

use spacers.

* Finishing is carried out in rows, each of which should be shifted by half of a tile. Facing is completed into the corners of

this room, and then immediately eliminate any remaining mortar at the joints.

Drying the walls requires no longer than a day and demands a constant humidity and temperature inside the room. The last point in

the laying of gypsum tiles is their own decoration. To try it, the joints between these components are full of a special solution,

the shade of which matches the brick.

Cosmetic fake of brickwork on the walls has been completed in the following ways:

* Cutting on the surface of the pits of masonry using a bolt cutter along with your hands;

* laying of tiles under the brick:

* mimicking the structure and color of the side of a single brick;

* Imitating a fragment of brickwork of several bricks.

The very best approach to decorate”under the brick” is really the one which allows you to create a usable coating with the maximum

appearance of its similarity to organic masonry. All three approaches to perform this kind of finishing functions fulfill the

prerequisites, but the cutting of joints with a bolt is labor-intensive and also the creation of large amounts of dust, so let’s

consider more prevalent manners.

The old finish is removed from the walls, and the surface, if needed, is leveled to eliminate the need to glue plaster onto a

thick coating of glue.

Combining such cladding with other types of interior finishes could be both orderly and done without any apparent consequences,

chaotically, together with fake of indications of aging.

With the help of cosmetic gypsum tiles it’s possible to mimic a large number of textures.

A lot of textures may be imitated with the support of cosmetic gypsum tiles.

The wall on which it is to be set up should have the following characteristics:

* Hardness and intensity of the outside;

* The lack of irregular locations and sharp sections;

* no more deformations.

Decorative tiles in the interior of this kitchen

Walls are made from a number of substances, so let’s break down the principles of installment.

When working with concrete, there will not be any big problems. It is just essential to take into account the porosity of the

material. Concrete, that has almost no pronounced pores, ought to be treated with a good primer.

Mounting gypsum tiles on concrete

Before beginning work on the installation of gypsum tiles on the walls, it is worth assessing the strength of this surface. After

the plaster doesn’t drop off the wall and at the identical time holds well, it is possible to simply paint it using primer.

Mount the tiles onto the painted concrete should not. The surface should be scratched, making sure to misfire, and it should be

grouted and covered with a layer of plaster.